FDA Label for Sterile Water
View Indications, Usage & Precautions
- DESCRIPTION
- CLINICAL PHARMACOLOGY
- INDICATIONS AND USAGE
- CONTRAINDICATIONS
- WARNINGS
- PRECAUTIONS
- ADVERSE REACTIONS
- DOSAGE AND ADMINISTRATION
- HOW SUPPLIED
- WARNING:
- TO OPEN
- PREPARATION FOR ADMINISTRATION AFTER RENDERING ISOTONIC
- TO ADD MEDICATION BEFORE ADMINISTRATION
- TO ADD MEDICATION DURING ADMINISTRATION
- PRINCIPAL DISPLAY PANEL
Sterile Water Product Label
The following document was submitted to the FDA by the labeler of this product Hikma Pharmaceuticals Usa Inc.. The document includes published materials associated whith this product with the essential scientific information about this product as well as other prescribing information. Product labels may durg indications and usage, generic names, contraindications, active ingredients, strength dosage, routes of administration, appearance, warnings, inactive ingredients, etc.
Description
Sterile Water for Injection, USP, is sterile, nonpyrogenic, distilled water in a single dose container for intravenous administration after addition of a suitable solute. It may also be used as a dispensing container for diluent use. No antimicrobial or other substance has been added. The pH is 5.5 (5.0 to 7.0). The osmolarity is 0.
The flexible plastic container is fabricated from polypropylene. The amount of water that can permeate from inside the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the plastic container may leach out certain chemical components from the plastic in very small amounts; however, biological testing was supportive of the safety of the plastic container materials.
Clinical Pharmacology
Sterile Water for Injection, USP is used for fluid replacement only after suitable additives are introduced to approximate isotonicity and to serve as a vehicle for suitable medications.
Indications And Usage
Sterile Water for Injection, USP is indicated in the aseptic preparation of parenteral solutions.
Contraindications
Sterile Water for Injection, USP is a hemolytic agent due to its hypotonicity. Therefore, it is contraindicated for intravenous administration without additives.
Warnings
Do not use for intravenous injection unless adjusted to approximate isotonicity with a suitable solute.
Hemolysis may occur following infusion of Sterile Water for Injection, USP. Hemoglobin induced renal failure has been reported following hemolysis.
Precautions
Do not administer unless solution is clear and seal is intact.
Adverse Reactions
The administration of a suitable admixture of prescribed additives may be associated with adverse reactions because of the solution or the technique of administration including febrile response, infection at the site of injection, venous thrombosis or phlebitis extending from the site of injection, extravasation, and hypervolemia.
If an adverse reaction does occur, discontinue the infusion, evaluate the patient, institute appropriate therapeutic countermeasures, and save the remainder of the fluid for examination if deemed necessary.
To report SUSPECTED ADVERSE REACTIONS, contact Hikma Pharmaceuticals USA Inc. at 1-877-845-0689, or the FDA at 1-800-FDA-1088 or www.fda.gov/medwatch.
For Product Inquiry call 1-877-845-0689.
Dosage And Administration
Following suitable admixture of prescribed additives, the dosage is usually dependent upon the age, weight and clinical condition of the patient as well as laboratory determinations. See directions accompanying additive drug.
Parenteral drug products should be inspected visually for particulate matter and discoloration prior to administration whenever solution and container permit.
Injections in flexible plastic containers are intended for intravenous administration using sterile equipment.
Additives may be incompatible. Complete information is not available. Those additives known to be incompatible should not be used. Consult with pharmacist, if available. If, in the informed judgment of the physician, it is deemed advisable to introduce additives, use aseptic technique. Do not store an unused portion of Sterile Water for Injection, USP. Mix thoroughly when additives have been introduced. Do not store solutions containing additives.
How Supplied
Sterile Water for Injection, USP is supplied in flexible plastic containers; 12 bags per carton as follows:
Strength | Package | NDC Number |
1000 mL | Single Bag | 0143-9339-01 |
12 Bags per carton | 0143-9339-12 |
Exposure of pharmaceutical products to heat should be minimized. Avoid excessive heat. It is recommended the product be stored at 20° to 25°C (68° to 77°F) [See USP Controlled Room Temperature]; brief exposure up to 40°C does not adversely affect the product.
Warning:
Do not use plastic containers in series connections. Such use could result in air embolism due to residual air being drawn from the primary container before administration of the fluid from the secondary container is completed.
Additives may be incompatible.
To Open
Tear overwrap at notch and remove solution container. Visually inspect the container. If the port outlet protector is damaged, detached, or not present, discard container as solution path sterility may be impaired. Some opacity of the plastic due to moisture absorption during the sterilization process may be observed. This is normal and does not affect the solution quality or safety. The opacity will diminish gradually. Check for minute leaks by squeezing inner bag firmly. If leaks are found, discard solution as sterility may be impaired. See following directions.
Preparation For Administration After Rendering Isotonic
- Suspend container from eyelet support.
- Remove plastic protector from outlet port at bottom of container.
- Attach administration set. Refer to complete directions accompanying set.
To Add Medication Before Administration
- Prepare medication site.
- Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.
- Mix solution and medication thoroughly. For high density medication such as potassium chloride, squeeze ports while ports are upright and mix thoroughly.
To Add Medication During Administration
- Close clamp on the set.
- Prepare medication site.
- Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject.
- Remove container from IV pole and/or turn to an upright position.
- Evacuate both ports by squeezing them while container is in the upright position.
- Mix solution and medication thoroughly.
- Return container to in use position and continue administration.
Principal Display Panel
* Please review the disclaimer below.