Sodium Chloride Solution
FDA Label NDC 0338-0050

Sodium Chloride Processing Solution is a sterile, nonpyrogenic solution in single dose container for use in blood cell processing devices. It contains no antimicrobial agents. Composition, osmolarity, pH, and ionic concentration are shown in Table 1.

The plastic container is fabricated from a specially formulated polyvinyl chloride (PL 146 Plastic). The amount of water that can permeate from inside the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the plastic container can leach out certain of its chemical components in very small amounts within the expiration period, e.g., di-2-ethylhexylphthalate (DEHP), up to 5 parts per million. However, the safety of the plastic has been confirmed in tests in animals according to USP biological tests for plastic containers as well as by tissue culture toxicity studies.

0.9% Sodium Chloride Processing Solution has value as a physiological blood cell processing aid.

0.9% Sodium Chloride Processing Solution is indicated in processing blood cells.

See directions accompanying blood cell processing device for complete instructions for use.

None known

This container should not be connected for direct intravenous administration.

The contents of an opened container should be used promptly to minimize the possibility of bacterial growth or pyrogen formation. Discard the unused portion of processing solution.

Careful review and understanding of the use of this solution in conjunction with blood cell processing equipment is essential.

Animal reproduction studies have not been conducted with 0.9% Sodium Chloride Processing Solution. It is also not known whether 0.9% Sodium Chloride Processing Solution can cause fetal harm when administered to a pregnant woman or can affect reproduction capacity. 0.9% Sodium Chloride Processing Solution should be given to a pregnant woman only if clearly needed.

Safety and effectiveness in pediatric patients have not been established.

Do not administer unless solution is clear and seal is intact.

None known

As directed by a physician. See directions accompanying blood cell processing device.

Processing Solutions should be inspected visually for particulate matter and discoloration prior to use.

0.9% Sodium Chloride Processing Solution in Flexible Plastic Container is available as follows:

Exposure of pharmaceutical products to heat should be minimized. Avoid excessive heat. It is recommended the product be stored at room temperature (25° C); brief exposure up to 40° C does not adversely affect the product.

Tear overwrap down side at slit and remove solution container. Visually inspect the container. If the outlet port protector is damaged, detached, or not present, discard container as solution path sterility may be impaired. Some opacity of the plastic due to moisture absorption during the sterilization process may be observed. This is normal and does not affect the solution quality or safety. The opacity will diminish gradually. Check for minute leaks by squeezing inner bag firmly. If leaks are found, discard solution as sterility may be impaired.

• 1.Suspend container from eyelet support.
• 2.Remove plastic protector from outlet port at bottom of container.
• 3.Attach to blood cell processing device. Refer to complete directions accompanying blood cell processing device.

Baxter Healthcare Corporation
Deerfield, IL 60015 USA

Printed in USA

©Copyright 1983, 1990, 1995, Baxter Healthcare Corporation. All rights
reserved.

07-19-73-065

Rev. May 2014

BAXTER, AND PL 146 ARE TRADEMARKS OF BAXTER INTERNATIONAL INC.

Sodium Chloride Representative Container Label (Image 01)

3000 mL

2B7207
NDC 0338-0050-47

NOT FOR INJECTION

0.9%
SODIUM CHLORIDE
Processing Solution

EACH 100 mL CONTAINS 900 mg SODIUM CHLORIDE USP
NO ANTIMICROBIAL AGENT HAS BEEN ADDED pH 5.5 (4.5 TO 7.0)
mEq/L SODIUM 154 CHLORIDE 154 OSMOLARITY 308
mOsmol/L (CALC) STERILE NONPYROGENIC SINGLE DOSE
CONTAINER

DOSAGE AS DIRECTED BY A PHYSICIAN SEE DIRECTIONS
ACCOMPANYING BLOOD CELL PROCESSING DEVICE FOR USE THIS
CONTAINER SHOULD NOT BE CONNECTED FOR DIRECT INTRAVENOUS
ADMINISTRATION

CAUTIONS SQUEEZE AND INSPECT INNER BAG WHICH MAINTAINS
PRODUCT STERILITY DISCARD IF LEAKS ARE FOUND DO NOT USE
UNLESS SOLUTION IS CLEAR DISCARD UNUSED PORTION RX ONLY
STORE UNIT IN MOISTURE BARRIER OVERWRAP AT ROOM TEMPERATURE
(25°C) UNTIL READY TO USE AVOID EXCESSIVE HEAT SEE INSERT

0.9%
Sodium Chloride
NaCl
Processing Solution

VIAFLEX CONTAINER

PL146 PLASTIC
FOR PRODUCT INFORMATION

1-800-933-0303

Baxter Logo
Baxter Healthcare Corporation
Deerfield, IL 60015 USA

Made in USA

Baxter VIAFLEX and
PL 146 are trademarks of
Baxter International Inc

Sodium Chloride Representative Carton Label (Image 02)

2B7207

4-3000 ML
PLASTIC CONTAINER

0.9% SODIUM CHLORIDE PROCESSING SOLUTION

EXP
XXXXX

SECONDARY BAR CODE
(17) YYMM00 (10) XXXXX

LOT
XXXXX

PRIMARY BAR CODE
(01) 50303380050470