Mechanism of Action
Trimethoprim blocks the production of tetrahydrofolic acid from dihydrofolic acid by binding to and reversibly inhibiting the required enzyme, dihydrofolate reductase. This binding is very much stronger for the bacterial enzyme than for the corresponding mammalian enzyme. Thus, trimethoprim selectively interferes with bacterial biosynthesis of nucleic acids and proteins.
Resistance
Resistance to trimethoprim may be conferred by a variety of mechanisms including cell wall impermeability, overproduction of the chromosomal dihydrofolate reductase (DHFR) enzyme, production of a resistant chromosomal DHFR enzyme or production of a plasmid-mediated trimethoprim-resistant DHFR enzyme. Acinetobacter baumannii/Acinetobacter calcoaceticus complex, Burkholderia cepacia complex, Pseudomonas aeruginosa, Stenotrophomonas maltophilia are intrinsically resistant to trimethoprim. Non-Enterobacteriaceae fecal organisms, Bacteroides spp. and Lactobacillus spp. are not susceptible to trimethoprim at the concentrations obtained with the recommended dosage. Enterococcus spp, (E. faecalis, E. faecium, E. gallinarum/E. casseliflavus) may appear active in vitro to trimethoprim but are not effective clinically and should not be reported as susceptible. Moraxella catarrhalis isolates were found consistently resistant to trimethoprim.
Antimicrobial Activity
Trimethoprim has been shown to be active against most strains of the following microorganisms, both in vitro and in clinical infections as described in the INDICATIONS AND USAGE section.
Aerobic gram-positive bacteria
Staphylococcus species (coagulase-negative strains, including S. saprophyticus)
Aerobic gram-negative bacteria
Enterobacter species
Escherichia coli
Klebsiella pneumoniae
Proteus mirabilis
Susceptibility Test Methods
When available, the clinical microbiology laboratory should provide cumulative reports of in vitro susceptibility test results for antimicrobial drugs used in local hospitals and practice areas to the physician as periodic reports that describe the susceptibility profile of nosocomial and community-acquired pathogens. These reports should aid the physician in selecting an antibacterial drug for treatment.
Dilution techniques
Quantitative methods are used to determine antimicrobial minimum inhibitory concentrations (MIC's). These MIC's provide estimates of the susceptibility of bacteria to antimicrobial compounds. The MIC's should be determined using a standardized procedure (broth and/or agar)1,7. The MIC values should be interpreted according to the criteria provided in Table 1.
Diffusion techniques
Quantitative methods that require measurement of zone diameters can also provide reproducible estimates of the susceptibility of bacteria to antimicrobial compounds. The zone size should be determined using a standardized test method.2,7 This procedure uses paper disks impregnated with 5 mcg trimethoprim to test the susceptibility of bacteria to trimethoprim. The disc diffusion breakpoints are provided in Table 1.
Table 1. Susceptibility Test Interpretive Criteria for Trimethoprim
|
Pathogen
| Minimum Inhibitory Concentrations (mcg/mL)
| Zone Diameters (mm)
|
S
| I
| R
| S
| I
| R
|
Enterobacteriaceae
| ≤ 8
| -
| ≥ 16
| ≥ 16
| 11-15
| ≤ 10
|
Coagulase negative staphylococci (including S. saprophyticus )
| ≤ 8
| -
| ≥ 16
| ≥ 16
| 11-15
| ≤ 10
|
A report of Susceptible (S) indicates that the antimicrobial drug is likely to inhibit growth of the pathogen if the antimicrobial drug reaches the concentration usually achievable at the site of infection. A report of Intermediate (I) indicates that the result should be considered equivocal, and, if the microorganism is not fully susceptible to alternative, clinically feasible drugs, the test should be repeated. This category implies possible clinical applicability in body sites where the drug is physiologically concentrated or in situations where a high dosage of the drug can be used. This category also provides a buffer zone that prevents small uncontrolled technical factors from causing major discrepancies in interpretation. A report of Resistant (R) indicates that the antimicrobial drug is not likely to inhibit growth of the pathogen if the antimicrobial drug reaches the concentration usually achievable at the infection site; other therapy should be selected.
Quality Control
Standardized susceptibility test procedures require the use of laboratory controls to monitor and ensure the accuracy and precision of supplies and reagents used in the assay, and the techniques of the individuals performing the test 1,2,7. Standard trimethoprim powder should provide the following range of MIC values noted in Table 2. For the diffusion technique using the 5 mcg disk, the criteria in Table 2 should be achieved.
Table 2: Quality Control Parameters for Trimethoprim
|
QC Strain
| Minimum Inhibitory Concentrations (mcg/mL)
| Zone Diameters (mm)
|
Enterococcus faecalis ATCC 29212
| 0.12 - 0.5
| --
|
Escherichia coli ATCC 25922
| 0.5 - 2
| 21 - 28
|
Haemophilus influenzae ATCC 49247
| 0.06 - 0.5
| 27 - 33
|
Staphylococcus aureus ATCC 29213
| 1 - 4
| --
|
Staphylococcus aureus ATCC 25923
| --
| 19 - 26
|
Streptococcus pneumoniae ATCC 49619
| 1 - 4
| --
|
Pseudomonas aeruginosa ATCC 27853
| > 64
| --
|